Future-proof lighting with ease-of-install.An effective way to introduce different lighting moods. At the time of review, all components must be installed and fully functional.The 24V RGBW dimmer can be seamlessly integrated into the Loxone projects, enabling the intelligent control and automation of light sources, such as LED strip. – Loxone Water Sensors in appropriate roomsĪ Loxone Partner Consultant will review each project you submit for the Smart Home Bonus. – Loxone Smoke Detector in designated rooms* – Loxone Touch/Touch Pure/Touch Surface for control in each room – Loxone Valve Actuators for zoned heating control for each room/zone – The shading should be controlled either by a Geiger motor, our Shading Actuator or our Relay Extension – A Motion Sensor Tree in each room (unless using our Ceiling Light with inbuilt motion sensor) – A minimum of 80% of the lighting should be Loxone Tree. The following hardware must be included in a Loxone Smart Home project: To qualify, the following functions must be commissioned: The 3% bonus will be in the form of a credit note on your account. The Smart Home Bonus is available on projects where the components were purchased after. Have you commissioned a true Loxone Smart Home? If so, you’ll effectively receive an addition 3% discount off the list price of all the Loxone components you’ve used in this project. The device must not be used as part of safety-critical systems. The installation requires a suitable enclosure to ensure protection against contact, water and dust. The installation must be carried out by a qualified technician in accordance with all applicable regulations. Smart Actuators support dynamic fade times and can only be used with the Lighting Controller. Use device with Standard Actuator(s) or Smart Actuator(s) When selected, you will be notified via System Status or the Mailer if the device is no longer available or goes offline. This information can be found in the technical data of the light source. In the settings of the Smart TW actuator, the color temperature of the light source is set for warm white and cool white: The assignment of the connections is as follows: Two Smart TW actuators or one Smart TW actuator and two individual channels can be configured. Smart Tunable White actuators are supported by the Lighting Control block. Two outputs of the dimmer for cool white (CW) and warm white (WW) are combined per actuator. The color temperature can be adjusted from warm white to cool white by mixing the two colors.įor this purpose, Loxone Devices with RGBW Dimming outputs support the actuator type Smart Tunable White: Tunable White (TW) refers to lighting with white light that is adjustable in color temperature.įor this purpose, light sources such as LED strips are available that combine warm white light and cool white light. Output 1 - terminal red, output 2 - terminal green, output 3 - terminal blue, output 4 - terminal white If "Individual channels " is selected as actuator type in the properties of the device, the channel assignment is as follows: If no connection to a Miniserver can be established for two minutes, then pairing mode is activated for 30 minutes. To activate the pairing mode manually, switch off the power for 10 seconds, then switch it back on. This is indicated by the status LED flashing red/green/orange. In delivery state, pairing mode will be active after the power supply has been established. I … current, L … cable length, A … wire cross-section, ΔU … voltage drop, ρ … resistance, ρ= constant (0,0172 for copper) This can be determined using the following formula: The wire size should be selected so that the voltage drop is not more than 1 V. The cable should be kept as short as possible to reduce voltage drop. The Compact Dimmer can be used without a separate enclosure. The RGBW Dimmers is installed on a DIN rail in a suitable enclosure. The functions are identical.ĭatasheet RGBW 24V Compact Dimmer Air Table of Contents The device is also available in a compact housing (RGBW Compact Dimmer Air). The 4 outputs can be configured as one RGBW channel, or can be used as 4 separate channels. With the RGBW Dimmer Air, extra low-voltage LED fittings and LED strips can be dimmed using PWM and any useable colours can be mixed.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |